Difference between revisions of "MYRAbot's arm control (bioloid+arduino)"

Revision as of 19:00, 24 December 2013

< go back to main

Bioloid arm

The arm that we will use is that Carlos Rodríguez Hernández developed in the project MYRA Robot: Hardware Update . The main components are:

Photograph of Bioloid arm.

• Arduino mega 2560 board.
• 74LS241 chip (tree-state Buffer).
• Voltage regulator circuit.
• 5 serial servo motors Dynamixel AX-12A.
• Mounting components of Bioloid kit.
• Parts made for the gripper and to fix to MYRAbot.

Arduino IDE and rosserial

For the communication among arduino and ROS, we install arduino IDE and rosserial (package de ROS which include the package rosserial_arduino with the libraries for arduino. We will start to installing arduino IDE, for this, we will execute the next commands in a terminal:

sudo apt-get update
sudo apt-get install arduino arduino-core

When the installation of arduino software ends, we will install the ROS package. For this, we will execute the next command in a terminal:

sudo apt-get install ros-ROS_DISTRO-rosserial

When we will have installed arduino IDE and the stack rosserial, we must copy the libraries for the package rosserial_arduino to the sketchbook of arduino. For this, we will execute the next commands in a terminal:

roscd rosserial_arduino/libraries
cp -r ros_lib /home/”SESSION_NAME”/sketchbook/libraries/ros_lib

Creating a package for our programs

Previously, we must have created a workspace for our ROS distribution. We will create a package in order to compile and send our programs to arduino board. We will make a package named "arduino_fer" with the the necessary dependences for our programs, for this, we will execute the next commands in a terminal:

cd ~/ros_workspace
roscreate-pkg arduino_fer rosserial_arduino std_msgs

We must change the content of the file "CMakeLists.txt" of our package for the next lines:

cmake_minimum_required(VERSION 2.4.6)
include($ENV{ROS_ROOT}/core/rosbuild/rosbuild.cmake)

rosbuild_find_ros_package(rosserial_arduino)
include(${rosserial_arduino_PACKAGE_PATH}/cmake_scripts/rosserial.cmake)

We will execute the next commands in a terminal to finalize the creation of the package:

roscd arduino_fer
cmake .

First program (To whole power)

We will make the first program that publishes a topic named "cifra" and subscribe a topic named "resultado". When we publish a number in the topic "cifra" the program multiplies the number by itself and publishes the result in the topic "resultado". The code of the program is shown below:

#include <ros.h> 
#include <std_msgs/Int16.h> 

ros::NodeHandle nh; 
int pot; 

void potencia( const std_msgs::Int16& cifra){ 

::pot = cifra.data*cifra.data; 
} 

ros::Subscriber<std_msgs::Int16> sub("cifra", &potencia ); 
std_msgs::Int16 res; 

ros::Publisher pub("resultado", &res); 

void setup() 
{ 
  nh.initNode(); 
  nh.subscribe(sub);  
  nh.advertise(pub); 
} 

void loop() 
{ 
  res.data = ::pot; 
  pub.publish( &res ); 
  nh.spinOnce(); 
  delay(1000); 
}

We must add to the file "CMakeLists.txt" the lines indicated below in order to compile the program and send to arduino board:

set(FIRMWARE_NAME potencia)

set(${FIRMWARE_NAME}_BOARD MODELO_NUESTRA_PLACA)   # Model of arduino board
set(${FIRMWARE_NAME}_SRCS src/potencia.cpp )
set(${FIRMWARE_NAME}_PORT /dev/ttyACM0)            # Serial port to upload
generate_ros_firmware(${FIRMWARE_NAME})

Here is set the name for the program, type of arduino board (uno, atmega328 o mega2560), name and address of the file, and serial port of the PC used to communicate with the board. We have to execute the next commands in a terminal:

roscd arduino_fer
make potencia-upload

We must launch the ROS core in a terminal to allow the execution of the program, if it is not already launched. We will execute the next command in a terminal:

roscore

In other terminal, we will execute the node that communicates ROS with the arduino board, we set the port that is used to communication. In order to know the port that is used, we can see the port used in the menu "Tools">"Serial port" of the software arduino IDE, the board must be plugged. In this case the port is "ttyACM0".

rosrun rosserial_python serial_node.py /dev/ttyACM0

We will execute in other terminal the next command to publish a number in the topic "cifra":

rostopic pub cifra std_msgs/Int16 NUMBER --once

We will execute in other terminal the next command to test that the program calculates the square of the published number in the topic "cifra" and publishes the result in the topic "resultado":

rostopic echo resultado

Arduino and servo motors Dinamixel

< go back to main